If you are a mechanical engineer specifying the finish on an aluminium enclosure, an NPI manager comparing finishing quotes that span $0.85 to $4.20 per square foot for what looks like the same process, or a hardware buyer trying to understand why a black anodised part costs more than a clear one \u2014 this guide is for you. Anodising is the most-quoted and least-understood finish in custom aluminium manufacturing. The pricing structure has three layers \u2014 process type, surface area, and add-ons \u2014 and most buyers see only the headline rate, miss the lot minimum, and budget 30 percent under the real number.<\/p>\n\n\n\n
At Yicen Precision we run anodising in-house as part of our sheet metal and CNC finishing capability. Roughly 40 percent of the aluminium parts we machine each month get some form of anodising \u2014 Type II clear or black on consumer-product housings, Type III hard-coat on aerospace and defence components, and the occasional Type I chromic on tight-fit aerospace brackets. This guide gives you the real 2026 cost ranges across all three types, the quantity curve that actually applies (not the round-number rule of thumb you usually see), and the DFM moves that typically cut anodising spend 20\u201335 percent without changing the finish spec.<\/p>\n\n\n\n
Every anodising quote \u2014 whether it comes from a job shop in California or an in-house finishing line in Shenzhen \u2014 is built from the same three buckets. The headline rate gets all the attention, but the lot charge and add-ons quietly drive the final invoice.<\/p>\n\n\n\n
Anodising Cost = Lot Charge + (Surface Area \u00d7 Rate per ft\u00b2) + Add-Ons<\/strong><\/p>\n\n\n\n The lot charge is a minimum per batch \u2014 covering tank setup, racking labour, dye preparation, and quality inspection. On a US job shop, lot charges run $75\u2013$200 per batch for Type II and $150\u2013$400 for Type III. This is why anodising a single small part can cost more per part than anodising 500 of them \u2014 at quantity one, you pay the full lot charge against one piece.<\/p>\n\n\n\n The per-square-foot rate is the variable component. It scales linearly with the wetted surface area of the part (the total exterior surface the chemistry touches) and with the chosen type and coating thickness. Add-ons cover sealing, dyeing in non-standard colours, pre-treatment such as bead blasting, and inspection above the lot baseline.<\/p>\n\n\n\n Anodising splits into three commercial processes, each with a different cost profile and a different application range. Picking the wrong type is the most expensive mistake we see in customer specs \u2014 Type III on a part that only needs Type II costs roughly 2.5 times more for no functional gain.<\/p>\n\n\n\n Two pricing notes from this table. First, Type I chromic anodise is more expensive than Type II despite being thinner, because of the controlled chromic-acid chemistry and the limited number of suppliers still running it under EPA regulations. Second, Type III commands a roughly 2.5\u20133\u00d7 premium over Type II \u2014 both because the coating itself is thicker and harder, and because tank time is longer and chiller capacity is required to keep the bath at 0\u20135 \u00b0C during the process.<\/p>\n\n\n\n This is where buyers get surprised most often. A 50 cm\u00b2 aluminium bracket has a wetted area of roughly 0.5 ft\u00b2. At a Type II rate of $1.20 per ft\u00b2, the variable cost is $0.60 per part. But the lot charge of $120 still applies \u2014 so one part costs $120.60, ten parts cost $126, and 200 parts cost $240 total ($1.20 per part). The unit cost crashes by 99 percent between qty 1 and qty 200, and most of that is just spreading the lot charge.<\/p>\n\n\n\n The practical lesson: do not anodise prototypes one at a time if you can batch them. Order three or four design iterations together and anodise them in a single run. The lot charge amortises immediately, and your prototype anodising spend drops by half or more.<\/p>\n\n\n\n Standard clear and black are the cheapest colours because most anodising shops keep those dye tanks running continuously. Specifying any non-standard colour \u2014 red, blue, gold, bronze, custom-mixed \u2014 adds $2\u2013$5 per part for the dye batch setup, plus typically 20\u201340 percent on the base rate because of the slower line throughput. Colour matching between production lots is also harder for custom colours, so expect more variance batch-to-batch.<\/p>\n\n\n\n From our quoting experience: if cosmetic appearance matters more than mechanical performance, specify Type II black or clear. If you absolutely need a specific colour, lock in a single supplier and a master colour standard sample early \u2014 switching anodising shops mid-production almost always shifts the colour just enough to be visible.<\/p>\n\n\n\n Anodising is priced by wetted surface area, not part weight or volume. A thin-walled enclosure with internal ribbing can have 2\u20134\u00d7 the surface area of a solid bar of the same outer dimensions \u2014 and will cost 2\u20134\u00d7 more to anodise. Designers who calculate finishing cost from part weight consistently underestimate the bill on hollow or finned geometries by 50\u201370 percent.<\/p>\n\n\n\n Different aluminium alloys anodise differently. 6061 and 6063 are the cheapest and most consistent \u2014 clean uniform colour, predictable coating thickness. 7075 anodises well but tends to come out slightly yellower than 6061 in clear finishes because of its zinc content. 2024 contains copper and requires special bath chemistry, adding 25\u201340 percent to the rate. Die-cast aluminium (A356, ADC12) anodises poorly and patchily and typically gets powder coated instead. If you specify anodising on die-cast parts, expect either a refusal or a high quote with a no-warranty disclaimer.<\/p>\n\n\n\n Bead blasting before anodising is the most common pre-treatment and produces the consistent matte finish you see on Apple products and high-end electronics. Bead blasting adds typically $0.30\u2013$1.00 per ft\u00b2 and significantly improves cosmetic uniformity. Chemical brightening or polishing before anodising produces a mirror-like finish but adds $1.50\u2013$3.00 per ft\u00b2 and is only justified for visual-grade decorative work.<\/p>\n\n\n\n Hot-water sealing or nickel-acetate sealing improves corrosion resistance and dye fastness but adds $0.25\u2013$1.00 per ft\u00b2. For outdoor or marine applications, sealing is non-negotiable \u2014 the cost is justified by the dramatic reduction in colour fading and corrosion. For interior or short-life parts, sealing can usually be skipped.<\/p>\n\n\n\n Anodising is one of the few processes where the China cost advantage is smaller than people expect. Chemistry, electricity, and chiller energy are similar costs globally. The gap shows up mostly in labour for racking and inspection, and in tank utilisation. Here is what we see across our customer base.<\/p>\n\n\n\n The savings on the per-square-foot rate are roughly 35\u201345 percent \u2014 meaningful but not enormous. The bigger savings come from the lot charges, where Chinese in-house lines typically charge 60\u201370 percent less than US job shops because the line is co-located with the machine shop and there is no separate freight or batching overhead. For prototype quantities under 50 units, this lot-charge gap is what makes Chinese sourcing genuinely cheaper. Above 500 units, the difference shrinks.<\/p>\n\n\n\n Here is a realistic worked example showing where anodising sits in the total cost of a finished part. The part: a CNC-machined 6061 aluminium enclosure, 100 mm \u00d7 60 mm \u00d7 25 mm, with 2.0 mm walls and internal ribbing, Type II black anodise.<\/p>\n\n\n\n Two observations from this example. First, anodising adds roughly 10 percent to the cost of a finished CNC aluminium part at production volumes \u2014 not the 30\u201350 percent that buyers often assume. Second, the anodising share is much higher at prototype quantities (19 percent at qty 10) because of the lot charge. If you are evaluating quotes that quote anodising at 30 percent of CNC cost on a 100-piece order, that is a red flag \u2014 either the CNC pricing is too low, the anodising rate is too high, or the supplier is double-billing the lot charge.<\/p>\n\n\n\n It depends almost entirely on quantity, surface area, and type. For a typical consumer-electronics enclosure with about 0.4 ft\u00b2 of wetted surface in Type II black anodise: roughly $13\u2013$25 per part in the US at quantity 10, $1.50\u2013$3.00 per part at quantity 200, and $1.00\u2013$1.80 per part at quantity 1,000. At Yicen Precision, those same quantities run $5\u2013$12, $0.70\u2013$1.40, and $0.50\u2013$1.00 respectively.<\/p>\n\n\n\n Anodising is an electrochemical conversion of the aluminium surface into aluminium oxide \u2014 the coating is part of the substrate. Powder coating is a sprayed polymer film bonded to the metal by heat. Anodised parts are thinner, harder, more abrasion-resistant, and conduct heat better; powder-coated parts are thicker, better at hiding surface imperfections, and available in more colours including textures. For aluminium, anodising is the more durable finish for most applications; for steel or galvanised steel, powder coating is the only option.<\/p>\n\n\n\n Two reasons. First, black dye is the most cost-controlled premium dye and the most quality-controlled because any colour variation is obvious. Second, achieving deep uniform black requires a thicker anodic layer (typically 15\u201320 \u00b5m versus 8\u201312 \u00b5m for clear), which means more tank time and more electrical energy. The premium is usually 15\u201325 percent over clear.<\/p>\n\n\n\n Stainless steel cannot be anodised in the traditional sense \u2014 the chemistry only works on metals with native oxide layers like aluminium, magnesium, titanium, niobium, and tantalum. Titanium can be anodised, but it produces interference colours (gold, blue, purple, green) by varying voltage rather than dye, and costs typically 3\u20135\u00d7 per ft\u00b2 compared to aluminium Type II. For stainless steel, the equivalent process is electropolishing or passivation.<\/p>\n\n\n\n We operate Type II and Type III anodising lines in our Shenzhen finishing facility, alongside bead blasting, chemical brightening, and sealing. Co-locating finishing with our CNC and sheet metal shops eliminates freight between processes and lets us batch parts efficiently. Standard lead time for Type II anodising on machined parts is 2\u20134 days; Type III runs 4\u20136 days. Full inspection documentation included with every order.<\/p>\n\n\n\n If you have aluminium parts that need machining plus anodising, we handle both in-house. Send a STEP file and your finishing spec \u2014 type, colour, thickness, sealing requirement \u2014 and we will quote the full machine-and-finish cost within 12 working hours.<\/p>\n\n\n\n Upload your STEP file at yicenprecision.com \u2014 tell us your anodising spec and we will quote the complete part.<\/strong><\/p>","protected":false},"excerpt":{"rendered":" Anodising Cost Guide 2026 \u2014 Pricing by Type, Volume, and Colour If you are a mechanical engineer specifying the finish on an aluminium enclosure, an NPI manager comparing finishing quotes that span $0.85 to $4.20 per square foot for what looks like the same process, or a hardware buyer trying to understand why a black […]<\/p>\n","protected":false},"author":12,"featured_media":26898,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"_seopress_robots_primary_cat":"","_seopress_titles_title":"Anodising Cost Guide 2026 \u2014 Pricing by Type, Volume, and Colour","_seopress_titles_desc":"Real 2026 anodising costs by type, surface area, colour, and quantity. Type II vs Type III rates, lot-charge minimums, US vs China pricing, and the DFM moves that cut anodising spend.","_seopress_robots_index":"","_seopress_analysis_target_kw":"","footnotes":""},"categories":[22],"tags":[],"class_list":{"0":"post-26897","1":"post","2":"type-post","3":"status-publish","4":"format-standard","5":"has-post-thumbnail","7":"category-blog"},"acf":[],"_links":{"self":[{"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/posts\/26897","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/users\/12"}],"replies":[{"embeddable":true,"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/comments?post=26897"}],"version-history":[{"count":1,"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/posts\/26897\/revisions"}],"predecessor-version":[{"id":26899,"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/posts\/26897\/revisions\/26899"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/media\/26898"}],"wp:attachment":[{"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/media?parent=26897"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/categories?post=26897"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/yicenprecision.com\/de\/wp-json\/wp\/v2\/tags?post=26897"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}The Three Anodising Types \u2014 Cost and Use<\/h2>\n\n\n\n
Typ<\/strong><\/td> Common Name<\/strong><\/td> Dicke der Beschichtung<\/strong><\/td> Rate (USD\/ft\u00b2)<\/strong><\/td> Typische Verwendung<\/strong><\/td><\/tr><\/thead> Type I<\/td> Chromic Acid<\/td> 0.5\u20137.5 \u00b5m<\/td> $0.70\u2013$3.00<\/td> Aerospace fatigue-critical, tight-tolerance fits<\/td><\/tr> Typ II<\/td> Sulphuric Acid<\/td> 5\u201325 \u00b5m<\/td> $0.50\u2013$2.00<\/td> Decorative, electronics, consumer products<\/td><\/tr> Type II clear<\/td> Standard clear<\/td> 8\u201315 \u00b5m<\/td> $0.50\u2013$1.40<\/td> General-purpose, electronics housings<\/td><\/tr> Type II black<\/td> Standard black<\/td> 10\u201320 \u00b5m<\/td> $0.80\u2013$2.00<\/td> Cosmetic, anti-glare optical<\/td><\/tr> Type III<\/td> Hard Anodise<\/td> 25\u2013100 \u00b5m<\/td> $2.00\u2013$5.00<\/td> Wear-resistant, military, fluid-handling<\/td><\/tr> Type III black<\/td> Hard-coat black<\/td> 30\u201380 \u00b5m<\/td> $2.50\u2013$5.50<\/td> Aerospace, firearm components, hydraulics<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n What Drives Anodising Cost \u2014 Beyond the Per-Square-Foot Rate<\/h2>\n\n\n\n
Quantity and the Lot Charge<\/h3>\n\n\n\n
Menge<\/strong><\/td> Total Cost (Type II clear)<\/strong><\/td> Per-Part Cost<\/strong><\/td> vs Single Unit<\/strong><\/td><\/tr><\/thead> 1<\/td> $120.60<\/td> $120.60<\/td> \u2014<\/td><\/tr> 10<\/td> $126.00<\/td> $12.60<\/td> \u221290%<\/td><\/tr> 50<\/td> $150.00<\/td> $3.00<\/td> \u221298%<\/td><\/tr> 100<\/td> $180.00<\/td> $1.80<\/td> \u221298.5%<\/td><\/tr> 200<\/td> $240.00<\/td> $1.20<\/td> \u221299%<\/td><\/tr> 500<\/td> $420.00<\/td> $0.84<\/td> \u221299.3%<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n Colour Choice<\/h3>\n\n\n\n
Surface Area, Not Part Weight<\/h3>\n\n\n\n
Alloy Choice<\/h3>\n\n\n\n
Pre-Treatment Requirements<\/h3>\n\n\n\n
Versiegeln<\/h3>\n\n\n\n
US vs China \u2014 Real Anodising Cost Comparison<\/h2>\n\n\n\n
Process \/ Add-On<\/strong><\/td> USA<\/strong><\/td> Germany \/ EU<\/strong><\/td> China (Tier 1)<\/strong><\/td> Yicen Pr\u00e4zision<\/strong><\/td><\/tr><\/thead> Type II clear, per ft\u00b2<\/td> $0.90\u2013$1.80<\/td> \u20ac1.00\u2013\u20ac1.85<\/td> $0.50\u2013$1.10<\/td> $0.45\u2013$1.00<\/td><\/tr> Type II black, per ft\u00b2<\/td> $1.20\u2013$2.10<\/td> \u20ac1.30\u2013\u20ac2.20<\/td> $0.70\u2013$1.40<\/td> $0.65\u2013$1.30<\/td><\/tr> Type III hard, per ft\u00b2<\/td> $2.50\u2013$4.80<\/td> \u20ac2.60\u2013\u20ac4.90<\/td> $1.50\u2013$3.00<\/td> $1.40\u2013$2.80<\/td><\/tr> Lot charge \u2014 Type II<\/td> $75\u2013$200<\/td> \u20ac80\u2013\u20ac200<\/td> $30\u2013$80<\/td> $25\u2013$70<\/td><\/tr> Lot charge \u2014 Type III<\/td> $150\u2013$400<\/td> \u20ac160\u2013\u20ac420<\/td> $60\u2013$150<\/td> $55\u2013$140<\/td><\/tr> Sealing, per ft\u00b2<\/td> $0.40\u2013$1.00<\/td> \u20ac0.45\u2013\u20ac1.00<\/td> $0.20\u2013$0.60<\/td> $0.18\u2013$0.55<\/td><\/tr> Bead blast prep, per ft\u00b2<\/td> $0.50\u2013$1.00<\/td> \u20ac0.55\u2013\u20ac1.10<\/td> $0.20\u2013$0.50<\/td> $0.18\u2013$0.45<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n Combined CNC + Anodise Pricing \u2014 Real Example<\/h2>\n\n\n\n
Stage<\/strong><\/td> Quantity 10<\/strong><\/td> Quantity 100<\/strong><\/td> Quantity 500<\/strong><\/td><\/tr><\/thead> Wetted surface area<\/td> 0.42 ft\u00b2 each<\/td> 0.42 ft\u00b2 each<\/td> 0.42 ft\u00b2 each<\/td><\/tr> CNC machining cost (Yicen)<\/td> $22.50 each<\/td> $11.80 each<\/td> $8.20 each<\/td><\/tr> Bead blast prep<\/td> $0.20 each<\/td> $0.18 each<\/td> $0.18 each<\/td><\/tr> Type II black anodise (rate)<\/td> $0.45 each<\/td> $0.42 each<\/td> $0.40 each<\/td><\/tr> Lot charge \u2014 anodise<\/td> $4.50 each (\u221510)<\/td> $0.45 each (\u2215100)<\/td> $0.10 each (\u2215500)<\/td><\/tr> Versiegeln<\/td> $0.18 each<\/td> $0.16 each<\/td> $0.16 each<\/td><\/tr> Total finished part<\/td> $27.83 each<\/td> $13.01 each<\/td> $9.04 each<\/td><\/tr> Anodise share of total cost<\/td> 19%<\/td> 9%<\/td> 10%<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n DFM Tips That Cut Anodising Cost<\/h2>\n\n\n\n
\n
FAQs \u2014 Anodising Cost<\/h2>\n\n\n\n
How much does anodising cost per part?<\/h3>\n\n\n\n
How is anodising different from powder coating?<\/h3>\n\n\n\n
Why does black anodising cost more than clear?<\/h3>\n\n\n\n
Can I anodise stainless steel or titanium?<\/h3>\n\n\n\n
How does Yicen Precision handle anodising in-house?<\/h3>\n\n\n\n
Get a CNC + Anodise Quote from Yicen Precision<\/h2>\n\n\n\n
\n