{"id":26932,"date":"2026-06-01T13:55:36","date_gmt":"2026-06-01T13:55:36","guid":{"rendered":"https:\/\/yicenprecision.com\/?p=26932"},"modified":"2026-06-04T14:06:56","modified_gmt":"2026-06-04T14:06:56","slug":"milling-fixtures-types-design-examples","status":"publish","type":"post","link":"https:\/\/yicenprecision.com\/pt\/milling-fixtures-types-design-examples\/","title":{"rendered":"Dispositivos de fresagem: tipos, princ\u00edpios de conce\u00e7\u00e3o e exemplos reais"},"content":{"rendered":"

Revisado pela Equipa de Engenharia de Precis\u00e3o da Yicen | \u00daltima atualiza\u00e7\u00e3o: junho de 2026<\/em><\/p>\n\n\n\n

A milling fixture is a workholding device that locates, supports, and clamps a workpiece in one fixed, repeatable position relative to the milling cutter and the machine table, so that identical parts can be machined accurately without marking out each one by hand. Unlike a jig, a fixture does not guide the cutter. The tool is set to the work using a set block and a feeler gauge, and the fixture itself is keyed to the machine table so every part sits exactly where the last one did.<\/p>\n\n\n\n

That single sentence carries the whole reason fixtures exist. On the shop floor, the difference between a part that holds tolerance across a run of 500 and a part that drifts after the first dozen almost always comes down to how the work is held. We design and build milling fixtures as part of our jig and fixture work, and the patterns below are the ones that decide whether a setup is fast, repeatable, and profitable, or slow and full of scrap.<\/p>\n\n\n\n

This guide covers what a milling fixture is, how the components work together, the classic and modern fixture types with the problem each one solves, the design rules that actually matter, material selection, a worked example, and the build-versus-buy decision.<\/p>\n\n\n\n

What a Milling Fixture Does (and Why It Is Not a Jig)<\/strong><\/h2>\n\n\n\n

A fixture solves three problems at once: location, support, and clamping.<\/p>\n\n\n\n

Location<\/strong> fixes the part in space so the same surface always faces the cutter. Support<\/strong> carries the cutting load and keeps the part from flexing or vibrating. Fixa\u00e7\u00e3o<\/strong> holds the part firmly against the locators without distorting it. Get any one of those wrong and the other two stop mattering.<\/p>\n\n\n\n

The point people miss is the tool relationship. A drilling jig has hardened bushings that physically steer the drill into the right spot. A milling fixture has no such guide. Instead, you set the cutter once against a set block, lock in that offset, and trust the fixture to present every part in the same place. This is why set blocks, tenons, and rigid bases matter so much in milling. The fixture is the only thing guaranteeing position.<\/p>\n\n\n\n

If you want the full breakdown of how the two devices differ, we cover it in our guide to the types of jigs and fixtures<\/a>. For this article, hold on to one rule: jigs guide the tool, fixtures position the work.<\/p>\n\n\n\n

The Core Components of a Milling Fixture<\/strong><\/h2>\n\n\n\n

Every milling fixture, from a simple plain fixture to a 4-axis tombstone, is built from the same functional parts. Understanding them is what lets you read or design a fixture quickly.<\/p>\n\n\n\n

Componente<\/td>Fun\u00e7\u00e3o<\/td>Common choices<\/td><\/tr>
Fixture base \/ body<\/td>Carries cutting forces, resists vibration, anchors everything<\/td>Cast iron, welded steel, or aluminum tooling plate<\/td><\/tr>
Localizadores<\/td>Establish the part\u2019s position using the 3-2-1 principle<\/td>Rest pads, locating pins, V-blocks, machined nests<\/td><\/tr>
Bra\u00e7adeiras<\/td>Press the part against the locators without lifting or distorting it<\/td>Strap clamps, toggle clamps, cam clamps, hydraulic clamps<\/td><\/tr>
Set block (setting block)<\/td>Reference surface for positioning the cutter<\/td>Hardened, ground block offset by a feeler gauge<\/td><\/tr>
Tenons \/ table keys<\/td>Align the fixture to the machine table T-slots<\/td>Hardened keys fitted to the table slot width<\/td><\/tr>
Clamping bolts<\/td>Lock the fixture to the table<\/td>T-bolts and nuts in the table slots<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

A few of these deserve a closer look because they cause most of the problems we see in fixtures that come to us for redesign.<\/p>\n\n\n\n

Locators and the 3-2-1 Principle<\/strong><\/h3>\n\n\n\n

Good location is the foundation of a good fixture. The standard approach is the 3-2-1 principle: three points define the primary locating plane, two define the secondary plane, and one defines the tertiary, which together remove all six degrees of freedom. We have a full breakdown in our article on the Princ\u00edpio da localiza\u00e7\u00e3o 3-2-1<\/a>, and it is worth reading before you design anything, because a fixture that locates poorly cannot be saved by stronger clamping.<\/p>\n\n\n\n

The Set Block<\/strong><\/h3>\n\n\n\n

The set block is what makes a milling fixture repeatable without bushings. You position the cutter against the block using a feeler gauge of known thickness, usually a few thousandths, so the tool never actually contacts the reference surface. That gap protects both the cutter and the block while giving you a precise, repeatable offset. Skip the set block and your operator is back to eyeballing every setup, which defeats the purpose of the fixture.<\/p>\n\n\n\n

Tenons<\/strong><\/h3>\n\n\n\n

Tenons are small hardened keys on the underside of the fixture that drop into the milling table\u2019s T-slots. They square the fixture to the table travel so that table movement and cutter travel stay aligned. On a precision fixture, tenons are the difference between a part that comes out parallel and one that comes out tapered.<\/p>\n\n\n\n

Design Principles That Decide Whether a Fixture Works<\/strong><\/h2>\n\n\n\n

The textbooks list dozens of rules. In production, these are the ones that earn their keep.<\/p>\n\n\n\n

Direct cutting forces into solid metal.<\/strong> The thrust of the cutter should land on the fixture body or the locators, never on the clamps. Clamps hold the part in place. They are not built to absorb milling loads, which are heavy and interrupted because each cutter tooth strikes and releases many times a second.<\/p>\n\n\n\n

Clamp toward the locators, over supported areas.<\/strong> A clamp pressing on an unsupported span will bow the part, and the part will spring back out of tolerance once the clamp releases. Place clamps directly over rest pads or solid support.<\/p>\n\n\n\n

Keep the work low and close to the table.<\/strong> Height is the enemy of rigidity. The taller the part sits above the fixture base, the more leverage the cutting force has to induce chatter and deflection. Mounting the work close to the table is one of the cheapest ways to improve surface finish.<\/p>\n\n\n\n

Assegure a seguran\u00e7a da carga.<\/strong> Add a pin, a step, or an asymmetric rest so the part physically cannot be loaded backward or upside down. On a manual setup running hundreds of parts, this single feature prevents more scrap than any inspection step. This is the poka-yoke idea applied to workholding.<\/p>\n\n\n\n

Provide cutter clearance and chip evacuation.<\/strong> The cutter needs room to run off the edge of the cut without hitting the fixture, and chips and coolant need somewhere to go. Pooled chips lift parts off their locators and ruin position.<\/p>\n\n\n\n

Harden the wear surfaces.<\/strong> Locators and set blocks take repeated contact. Make them from a material you can harden, or use replaceable hardened inserts, so the fixture holds its accuracy across the life of the program.<\/p>\n\n\n\n

Match complexity to volume.<\/strong> A 50-part run does not justify a hydraulic dedicated fixture. A 50,000-part run cannot afford manual strap clamps. The right fixture is the one whose cost is justified by the production quantity, a tradeoff we walk through near the end of this guide.<\/p>\n\n\n\n

If you want the design workflow start to finish, our complete guide to designing jigs and fixtures<\/a> covers the full process.<\/p>\n\n\n\n

Types of Milling Fixtures<\/strong><\/h2>\n\n\n\n

Milling fixtures are usually named after how they present the work to the cutter or how many parts and surfaces they handle at once. Here is the classic taxonomy, with the problem each type solves.<\/p>\n\n\n\n

Plain (Simple) Milling Fixture<\/strong><\/h3>\n\n\n\n

The most basic form. The part is located and clamped on the fixture, the fixture is keyed to the table, and a single cutter machines one face or contour. Plain fixtures suit lower volumes and straightforward parts where you mainly need repeatable location, not high output.<\/p>\n\n\n\n

Solves:<\/strong> repeatable single-surface milling without marking out each part.<\/p>\n\n\n\n

Straddle Milling Fixture<\/strong><\/h3>\n\n\n\n

Two side cutters spaced on the arbor \u201cstraddle\u201d the workpiece and machine two parallel faces in a single pass. This is how you cut the flats on a bolt head or two parallel sides on a block in one operation. Because the cutting load is heavy and symmetrical, straddle fixtures must be very rigid, and the cutter spacing has to be controlled precisely.<\/p>\n\n\n\n

Solves:<\/strong> two parallel faces machined simultaneously, with guaranteed dimension between them.<\/p>\n\n\n\n

Gang Milling Fixture<\/strong><\/h3>\n\n\n\n

Several cutters of different shapes and diameters are ganged on one arbor to machine multiple surfaces at the same time. The fixture has to support the part against a complex combined load. Gang setups shine in higher-volume work where multiple features can be roughed or finished in one pass.<\/p>\n\n\n\n

Solves:<\/strong> several surfaces machined in one pass to cut cycle time.<\/p>\n\n\n\n

String (Line) Milling Fixture<\/strong><\/h3>\n\n\n\n

Multiple identical parts are loaded in a line along the table and milled in one continuous pass. The cutter never stops, so throughput is high. The fixture has to locate and clamp every station identically.<\/p>\n\n\n\n

Solves:<\/strong> high-volume production of small parts with maximum throughput per pass.<\/p>\n\n\n\n

Indexing Milling Fixture<\/strong><\/h3>\n\n\n\n

The fixture rotates the part to set angular positions between cuts, usually with an indexing plate and locking pin. This is how you mill slots at even intervals, square or hex forms, splines, and ratchet teeth.<\/p>\n\n\n\n

Solves:<\/strong> repeated features at precise angular spacing around a part.<\/p>\n\n\n\n

Profile (Form) Milling Fixture<\/strong><\/h3>\n\n\n\n

Built to hold and support irregular or contoured parts so a form cutter can follow the profile. The locating nest is often machined to match the part shape.<\/p>\n\n\n\n

Solves:<\/strong> holding awkward, non-prismatic parts steady for contour work.<\/p>\n\n\n\n

Reciprocating (Duplex) Milling Fixture<\/strong><\/h3>\n\n\n\n

Two stations sit on a sliding or rotating table. While one part is being machined, the operator unloads and reloads the other. The cycle never pauses for loading, so machine spindle time stays productive.<\/p>\n\n\n\n

Solves:<\/strong> eliminating load and unload downtime in continuous production.<\/p>\n\n\n\n

Rotary Table (Circular Feed) Milling Fixture<\/strong><\/h3>\n\n\n\n

Parts are mounted around a rotary table and fed continuously past the cutter. Like the reciprocating type, it overlaps loading time with cutting time, and it suits round or radially arranged features.<\/p>\n\n\n\n

Solves:<\/strong> continuous machining with loading hidden inside the cut cycle.<\/p>\n\n\n\n

Quick Comparison of Milling Fixture Types<\/strong><\/h3>\n\n\n\n
Fixture type<\/td>Melhor para<\/td>Parts per setup<\/td>Custo relativo<\/td><\/tr>
Plain<\/td>Single face, low to medium volume<\/td>1<\/td>Baixa<\/td><\/tr>
Straddle<\/td>Two parallel faces in one pass<\/td>1 to several<\/td>M\u00e9dio<\/td><\/tr>
Gang<\/td>Multiple surfaces in one pass<\/td>1 to several<\/td>M\u00e9dio a alto<\/td><\/tr>
String \/ line<\/td>High-volume small parts<\/td>Many<\/td>M\u00e9dio<\/td><\/tr>
Indexa\u00e7\u00e3o<\/td>Angular features, slots, splines<\/td>1<\/td>M\u00e9dio a alto<\/td><\/tr>
Profile \/ form<\/td>Irregular contoured parts<\/td>1<\/td>M\u00e9dio<\/td><\/tr>
Reciprocating \/ duplex<\/td>Continuous production, no idle loading<\/td>2 stations<\/td>Elevado<\/td><\/tr>
Rotary table<\/td>Continuous radial milling<\/td>Many<\/td>Elevado<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Modern CNC Milling Fixtures<\/strong><\/h2>\n\n\n\n

The classic taxonomy was written for manual and arbor-style milling. On a modern machining center, the same principles apply, but the hardware looks different. These are the workholding options you will actually choose between in a CNC shop today.<\/p>\n\n\n\n

Precision machine vise.<\/strong> The default for prismatic parts. Fast, accurate, and flexible. A good ground vise with parallels handles a large share of CNC milling work with no custom tooling at all.<\/p>\n\n\n\n

Soft jaws.<\/strong> Machinable jaws fitted to a vise and bored or stepped to match a specific part. They give you a custom locating profile in minutes for the cost of a block of aluminum, which makes them the cheapest path to a semi-dedicated fixture for short and medium runs.<\/p>\n\n\n\n

Fixture (tooling) plate.<\/strong> A flat plate with a grid of precision dowel and tapped holes that mounts to the table. It becomes the foundation for vises, modular components, or dedicated locating details, and it standardizes setups across jobs.<\/p>\n\n\n\n

Modular fixturing.<\/strong> Reconfigurable kits of bases, locators, and clamps that bolt together into a custom layout, then come apart and rebuild for the next job. Modular systems give you most of the benefit of a dedicated fixture without the dedicated cost, which is why they fit prototype and low-volume work so well.<\/p>\n\n\n\n

Vacuum fixture.<\/strong> Uses suction to hold thin, flat, or non-ferrous parts that clamps would distort, such as plates, panels, and gasket-like geometry. No clamps means no marks and full access to the top face.<\/p>\n\n\n\n

Tombstone and 4th or 5th-axis fixtures.<\/strong> Multi-sided fixtures mounted on a rotating axis so the machine can reach several faces, or several parts, in one setup. These cut the number of operations and the handling between them, which is where a lot of cost and error hides. They pair naturally with our CNC milling services<\/a>.<\/p>\n\n\n\n

Choosing a Fixture: Dedicated vs Modular vs Standard<\/strong><\/h2>\n\n\n\n

This is the decision that drives fixture cost and lead time, so it is worth a direct comparison.<\/p>\n\n\n\n

Fator<\/td>Standard (vise \/ soft jaws)<\/td>Modular<\/td>Dedicado (personalizado)<\/td><\/tr>
Custo inicial<\/td>Mais baixo<\/td>M\u00e9dio<\/td>Mais alto<\/td><\/tr>
Prazo de execu\u00e7\u00e3o<\/td>Imediato<\/td>Horas a dias<\/td>Dias a semanas<\/td><\/tr>
Velocidade de configura\u00e7\u00e3o na produ\u00e7\u00e3o<\/td>M\u00e9dio<\/td>M\u00e9dio<\/td>Mais r\u00e1pido<\/td><\/tr>
Repetibilidade<\/td>Bom<\/td>Bom<\/td>Melhor<\/td><\/tr>
Flexibilidade entre fun\u00e7\u00f5es<\/td>Elevado<\/td>Elevado<\/td>Nenhuma, espec\u00edfica da pe\u00e7a<\/td><\/tr>
Melhor gama de volume<\/td>Prot\u00f3tipo a baixo<\/td>Baixa a m\u00e9dia<\/td>M\u00e9dio a alto<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

The logic is simple. For prototypes and low volumes, standard workholding and soft jaws win because the tooling cost would never pay back. For high volumes, a dedicated fixture wins because faster load times and lower scrap are multiplied across thousands of parts. Modular sits in the middle and is often the smart default when you are not yet sure how a program will scale.<\/p>\n\n\n\n

Material Selection for the Fixture Body and Locators<\/strong><\/h2>\n\n\n\n

The fixture body and the wear surfaces have different jobs, so they usually call for different materials.<\/p>\n\n\n\n

Part of fixture<\/td>Typical materials<\/td>Porqu\u00ea<\/td><\/tr>
Fixture body \/ base<\/td>Cast iron, welded mild steel, aluminum tooling plate<\/td>Cast iron damps vibration well, steel offers strength and weldability, aluminum is light for modular and 4th-axis use<\/td><\/tr>
Locators and rest pads<\/td>Hardened tool steel, case-hardened steel<\/td>They take repeated part contact and must hold size<\/td><\/tr>
Set blocks<\/td>Hardened ground steel<\/td>Reference surface that cannot wear<\/td><\/tr>
Bushings (if any guiding)<\/td>Hardened tool steel<\/td>Wear resistance under sliding contact<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Cast iron remains a favorite for dedicated production fixtures because its natural damping fights the chatter that interrupted milling cuts produce. Aluminum tooling plate has taken over a lot of modular and 4th-axis work because the weight savings matter when the fixture itself is being rotated or moved often.<\/p>\n\n\n\n

A Worked Example: Indexing Fixture for Four Slots at 90 Degrees<\/strong><\/h2>\n\n\n\n

A common real-world job is milling four slots spaced evenly around a cylindrical part. Here is how the fixture earns its place.<\/p>\n\n\n\n

The part is located on its bore and a face, satisfying the primary and secondary locating planes. An indexing plate with four positions and a spring-loaded locking pin sets the angular position. The operator mills the first slot, withdraws the pin, rotates the part one quarter turn until the pin drops into the next position, and cuts again. Four cuts, four identical slots, no measuring between them.<\/p>\n\n\n\n

Without the fixture, the operator would have to measure and mark each 90-degree position on every part, then dial it in by hand, which is slow and inconsistent. The indexing fixture turns a skilled layout task into a load, cut, index, repeat cycle that a wider range of operators can run at speed with repeatable accuracy. That is the entire value proposition of a fixture in one job.<\/p>\n\n\n\n

Build vs Buy: When a Custom Milling Fixture Pays Off<\/strong><\/h2>\n\n\n\n

A custom fixture has a real upfront cost: design time, materials, machining, and validation. It pays for itself through three returns.<\/p>\n\n\n\n

Tempo de ciclo.<\/strong> Faster, foolproof loading shaves seconds off every part. Across a long run, seconds become hours of machine time.<\/p>\n\n\n\n

Redu\u00e7\u00e3o de res\u00edduos.<\/strong> Reliable location and foolproofing cut the mistakes that turn raw material and machine hours into rejected parts.<\/p>\n\n\n\n

Repetibilidade e flexibilidade laboral.<\/strong> A good fixture lets more operators run a job at the same quality, instead of depending on one person\u2019s setup skill.<\/p>\n\n\n\n

The rough rule we use: if the part is high volume, has tight tolerances, or is awkward to hold in standard workholding, a dedicated or modular fixture usually pays back quickly. For one-off prototypes, standard workholding and soft jaws are almost always the right call. When the math is somewhere in between, modular fixturing is the low-risk middle path.<\/p>\n\n\n\n

If you are weighing a custom fixture for a production part, our team handles fixture design and build as part of our servi\u00e7os de conce\u00e7\u00e3o de gabaritos e acess\u00f3rios personalizados<\/a>, and we will tell you honestly when standard workholding is the better answer.<\/p>\n\n\n\n

Perguntas mais frequentes<\/strong><\/h2>\n\n\n\n

What is a milling fixture?<\/strong> A milling fixture is a workholding device that locates, supports, and clamps a workpiece in a fixed, repeatable position on a milling machine table so identical parts can be machined accurately. It positions the part but does not guide the cutter, which is set to the work using a set block.<\/p>\n\n\n\n

What is the difference between a jig and a fixture in milling?<\/strong> A jig guides the cutting tool, usually with hardened bushings, while a fixture only holds and positions the workpiece. In milling, the cutter is set against a set block rather than guided, so milling almost always uses fixtures rather than jigs.<\/p>\n\n\n\n

What are the main types of milling fixtures?<\/strong> The classic types are plain, straddle, gang, string or line, indexing, profile or form, reciprocating or duplex, and rotary table fixtures. Modern CNC shops also use precision vises, soft jaws, fixture plates, modular systems, vacuum fixtures, and 4th or 5th-axis tombstone fixtures.<\/p>\n\n\n\n

What materials are milling fixtures made from?<\/strong> Fixture bodies are commonly cast iron, welded steel, or aluminum tooling plate. Locators, rest pads, and set blocks are usually made from hardened tool steel so they resist wear and hold their accuracy.<\/p>\n\n\n\n

What is a set block used for in a milling fixture?<\/strong> A set block is a hardened reference surface that lets the operator position the cutter accurately and repeatably. The cutter is set against the block using a feeler gauge of known thickness, so the tool never touches the block but the offset stays exact.<\/p>\n\n\n\n

Should I use a milling fixture or a vise?<\/strong> For prototypes and simple low-volume parts, a precision vise or soft jaws is faster and cheaper. For high volumes, tight tolerances, or awkward parts, a dedicated or modular fixture reduces cycle time and scrap enough to justify its cost.<\/p>\n\n\n\n

How much does a custom milling fixture cost?<\/strong> Cost depends on complexity, the number of locating and clamping features, whether clamping is manual or powered, and the materials. A simple plate-and-clamp fixture is modest, while a multi-station hydraulic or 4th-axis fixture is a larger investment that is justified by high production volume.<\/p>\n\n\n\n

Getting Milling Fixtures Right on Your Parts<\/strong><\/h2>\n\n\n\n

A milling fixture is not complicated machinery, but it rewards good engineering. Locate to the 3-2-1 principle, drive cutting forces into solid metal, clamp over support, keep the work low, and foolproof the load. Match the fixture type to your volume and your geometry, and choose between standard, modular, and dedicated workholding based on how the cost pays back over the run.<\/p>\n\n\n\n

If you have a production part that is fighting you in standard workholding, that is usually the signal that a purpose-built fixture will earn its keep. You can send us your part files for a quote<\/a> and our engineering team will recommend the workholding approach that fits your volume and tolerances, whether that is a custom fixture or something simpler.<\/p>","protected":false},"excerpt":{"rendered":"

Reviewed by the Yicen Precision Engineering Team | Last updated: June 2026 A milling fixture is a workholding device that locates, supports, and clamps a workpiece in one fixed, repeatable position relative to the milling cutter and the machine table, so that identical parts can be machined accurately without marking out each one by hand. […]<\/p>\n","protected":false},"author":12,"featured_media":26933,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"_seopress_titles_title":"Milling Fixtures: Types, Design & Examples Explained","_seopress_titles_desc":"Learn how milling fixtures locate, support, and clamp parts for accurate milling. Compare fixture types, design rules, materials, and a real example.","_seopress_robots_index":"","_seopress_robots_follow":"","_seopress_robots_imageindex":"","_seopress_robots_snippet":"","_seopress_robots_primary_cat":"","_seopress_robots_breadcrumbs":"","_seopress_robots_freeze_modified_date":"","_seopress_robots_custom_modified_date":"","_seopress_robots_canonical":"","_seopress_social_fb_title":"","_seopress_social_fb_desc":"","_seopress_social_fb_img":"","_seopress_social_fb_img_attachment_id":0,"_seopress_social_fb_img_width":0,"_seopress_social_fb_img_height":0,"_seopress_social_twitter_title":"","_seopress_social_twitter_desc":"","_seopress_social_twitter_img":"","_seopress_social_twitter_img_attachment_id":0,"_seopress_social_twitter_img_width":0,"_seopress_social_twitter_img_height":0,"_seopress_redirections_value":"","_seopress_redirections_enabled":"","_seopress_redirections_enabled_regex":"","_seopress_redirections_logged_status":"","_seopress_redirections_param":"","_seopress_redirections_type":0,"_seopress_analysis_target_kw":"milling fixture,milling fixtures,types of milling fixtures,milling fixture design,straddle milling fixture,indexing milling fixture,plain milling fixture,milling fixture components,CNC milling fixtures,milling fixture vs vise","footnotes":""},"categories":[22],"tags":[],"class_list":{"0":"post-26932","1":"post","2":"type-post","3":"status-publish","4":"format-standard","5":"has-post-thumbnail","7":"category-blog"},"acf":[],"_links":{"self":[{"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/posts\/26932","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/users\/12"}],"replies":[{"embeddable":true,"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/comments?post=26932"}],"version-history":[{"count":3,"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/posts\/26932\/revisions"}],"predecessor-version":[{"id":26938,"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/posts\/26932\/revisions\/26938"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/media\/26933"}],"wp:attachment":[{"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/media?parent=26932"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/categories?post=26932"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/yicenprecision.com\/pt\/wp-json\/wp\/v2\/tags?post=26932"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}